GENERAL DESCRIPTION
PLiOGRIP EPOXY RESIN PER 526/PLIOGRIP HARDENER PH110 is a epoxy liquid resin system formulated specially for the hand lay-up applications. It can also be used for casting or incapsulation for low voltage electrical electronic components. No volatiles are evolved and hence shrinkage is minimal which can be further reduced by incorporation of fillers like silica (for casting applications only).
PLiOGRIP EPOXY RES-IN PER 526 is an unmodified liquid epoxy resin of medium viscosity and PLiOGRIP PH 110 is a low viscosity room temperature curing liquid hardener. This system gives a short pot life and fast cure at normal ambient temperatures. Products made from this system can be subjected to working temperature of 100°C.
TYPICAL PROPERTIES OF PLiOGRIP EPOXY RESIN PER 526
| Properties | Values |
|---|---|
| Type | Unmodified liquid epoxy resin |
| Specific gravity @ 25°C | 1.14 -1.20 |
| Appearance | Clear to pale yellow liquid |
| Epoxy equivalent | 180 - 200 |
| @ 25°C (CPS) | 8500 - 13000 |
TYPICAL PROPERTIES OF PLiOGRIP HARDENER PH 110
| Properties | Values |
|---|---|
| Type | Aliphatic Amine |
| Appearance | Pale yellow liquid |
| Viscosity @ 25°C (CPS) | 20 - 30 |
MIX RATIO (PARTS BY WEIGHT) AND POT LIFE AT 25°C
| EPOXY RESIN PER 526 | HARDENER PH 110 | POT LIFE MINUTES |
| 100 | 11 - 13 | 30-40 |
CURING TIME:
| Curing temperature °C | 30 | 4 | 8 | 10 |
| Curing time | 14-24 hrs | 14-24 hrs | 14-24 hrs | 20-30 mins |
TYPICAL PROPERTIES OF UNFILLED CURED SYSTEM WHHOUT REINFORCEMENT
| Property | Value |
| Density (gm/cc) | 1.15 -1.2 |
| Tensile strength (kg/em' | 450 -700 |
| Tensile elongation (%) | 4-5 |
| Flexural strength (kg/em') Flexural | 1100 - 1300 |
| modulus (kg/em') Compressive | 24400 |
| strength (kg/em') Impact strength | 1200-1300 |
| (kg-em/em') | 100 0.4-0.5 |
| Water absorption (% w/w) @100°C. 1 hour | 0.02 |
| Dielectric loss factor tan Ii (50 Hz.) @25°C | 130-150 |
| Morten's HDT (0 C.) | |
| Dielectric constant (Er) @ 25°C. Value | 4.3 |
| resistivity Q (ohm-em) @ 25°C. Dielectric | 0.3-0.6 x 10 15 |
| strength@ 25 °C.(kV/cm) | 220-240 |
SAFETY PRECAUTION:
Direct contact of Resin/Hardener with skin should be avoided. Use of hand gloves while handling them is recommended. Splashes on the skin, if any, should be removed immediately with soap and lukewarm water or with a suitable remover.
STORAGE:
Should be stored in closed containers in cool condition away from direct sunlight. Shelf life of Resin & Hardener @ 25°C. is about 12 months from the date of manufacturing.
NOTE:
The information given in this literature is based on the present state of our knowledge but any conclu¬sions and recommendations are made without any liability on our part. Buyers and users should make their own assessment of our products under their own conditions and for their own requirements.
Esteem spirit temper too say adieus who direct.
Location
Location